Главная

USED ​​KABAN BA2030, 2020 YEAR OF PRODUCTION SINGLE-HEAD WELDING MACHINE, TURKEY
Single-head welding machine KABAN BA2030, year of manufacture 2020. The machine is in perfect condition, like new, checked, configured. We can show it in operation. It practically did not work, was used for about six months on non-standard and alterations. Warehouse storage, the machine is not used in series, if necessary, we can connect and start it for testing. Location - Samara. We can send to the TC in the Russian Federation, non-cash sale without VAT, there will be a whole package of documents - a supply agreement, UPD, acceptance certificate, TTN for transportation.

USED ​​YILMAZ FR225 2017 YEAR OLD COPY-MILLING MACHINE, TURKEY
Manual feed copy-milling machine YILMAZ FR-225, for milling a triple hole for handles, as well as a groove for a lock. Year of manufacture 2017, the machine is in excellent condition. Currently in warehouse storage. Location - Samara. We can send photos and videos WhatsApp, and also demonstrate the work in person if the client comes to the warehouse. We will help with shipment, pack the equipment in stretch film, we can hand it over to the TC. We sell by bank transfer without VAT, contract, acts pp, UPD and TTN.

USED ​​COMPRESSOR BEZHETSK KV-30 PISTON COMPRESSOR
Piston compressor Bezhetsk, model KV30 for 2400 liters per minute, receiver 500 liters. In excellent condition. Two used piston groups are installed. Complete maintenance was carried out with replacement of the main consumables - belts, bearings, main relays, starters, as well as replacement of oil and filters.
Location - Samara. Warehouse storage.
You can check, make a trial run in the warehouse. We will help with shipment.

USED ​​COMPRESSOR BEZHETSK KV-30 PISTON COMPRESSOR
Piston compressor Bezhetsk, model KV30 for 2400 liters per minute, receiver 500 liters. In excellent condition. One piston group is installed new. Complete maintenance was carried out with replacement of the main consumables - belts, bearings, main relays, starters, as well as replacement of oil and filters.
Location - Samara, Warehouse storage. You can check, make a test run in the warehouse. We will help with shipment.

Pneumatic corner crimping press for joining corners of aluminum structures. Manufacturer OZGENC, Turkey. Model OMRM 136. Year of manufacture 2014. Condition is excellent. Included - pedals, side supports, knives. Warehouse storage. Can be connected and checked. Location - Samara. Shipment - pickup, delivery by a transport company is possible.

3+1 Axis CNC CONTROLLED COPY ROUTER MACHINE
Brand: China SinonModel: GCGZD-CNC-800Input power source: 380V/50Hz or CustomziedTotal power: 5KwMain spindle power: 3.5kwMain spindle speed: 0-18000rpmX axis processing range: 800mmY axis processing range: 200mmZ axis processing range: 145mmDimension: 1300×1500×1700mmWeight: 800kg

SINON LJRZ2-CNC-600 * 6000
DOUBLE HEAD CNC AUTOMATIC CUTTING MACHINE, ARBITRARY ANGLES ADJUST
1. The double head CNC front saw is an advanced equipment used for cutting aluminum profiles.
2. This machine has a neat and stylish appearance, modeled on the European style.
3. The new closed-loop control system used in this machine is highly efficient, ensuring precise cutting.
4. The machine is equipped with a direct drive saw blade, which uses a lever-turn cutting type, making the blade feed by the pneumatic-hydraulic damping cylinder and ensuring smooth cutting.
5. The imported saw blade used in this machine has high precision, making the cutting surface smooth.
6. The cutting angle of the machine can be adjusted in the range of 45°~157.5° by the servo motor driving the speed reducer.

Thermal Break Assembly Machine

Thermal break assembly machine is used for producing thermal break aluminum profiles, including two machines: knurling machine with plastic strip inserter, rolling machine.

Thermal Break Machine Introduction:
Thermal break machine is used for producing thermal barrier aluminum profiles, including two machines: knurling machine with plastic strip inserter, rolling machine. The finished product as follows:
Two pieces of aluminum profiles are connected just by polyamide strip. Aluminum can transfer heat or cold very easily, its thermal conductivity is high. But polyamide strip’s thermal conductivity is very low, then can block the heat or cold transferring through aluminum.
Raw material of polyamide strip is 75% nylon and 25% glass-fiber, we call PA66 GF25 or polyamide
 Consist of
1 set of knurling machine with strip feeder device
1 set of rolling machine
Daily capacity is 5~6 Tons per 10 hours

Thermal Break Assembly Machine
Thermal break assembly machine is used for producing thermal break aluminum profiles, including two machines: knurling machine with plastic strip inserter, rolling machine.

Thermal Break Machine Introduction:
Thermal break machine is used for producing thermal barrier aluminum profiles, including two machines: knurling machine with plastic strip inserter, rolling machine. The finished product as follows:
Two pieces of aluminum profiles are connected just by polyamide strip. Aluminum can transfer heat or cold very easily, its thermal conductivity is high. But polyamide strip’s thermal conductivity is very low, then can block the heat or cold transferring through aluminum.
Raw material of polyamide strip is 75% nylon and 25% glass-fiber, we call PA66 GF25 or polyamide
 Consist of
1 set of CNC knurling machine with strip feeder device
1 set of CNC rolling machine
Daily capacity is 5~6 Tons per 10 hours

KABAN BB2030. TWO-HEAD WELDING MACHINE
The machine is in excellent condition, almost new. Year of manufacture 2012. Warehouse storage, the machine is fully configured, adjusted, prepared for sale and shipment.
We will help with shipment, we use a forklift in the work.
Cashless sale without VAT, we provide a package of documents for shipment - supply agreement, UPD, acceptance certificates, TTN for transportation.

SINON SJ02-350 SINGLE-HEAD PENDULUM SAW
Automatic single-head pendulum saw for cutting PVC profiles (350mm) Saw blade Φ350mm×φ30mm. Cutting width: Max 200mm Cutting height: Max 100mm. Cutting angle: 45/90/135

Double-head automatic front saw FIMTEC SD25/S4. Designed for cutting two PVC or aluminum profiles at the same time. Saw blades 500 mm, in good condition. The cut length of workpieces at 90 and 45 degrees corresponds to the standard, no errors or backlashes are observed. Cutting at an angle is also within the standard, the angles after cutting match the specified parameters.
The machine is located in our warehouse in Samara, is not in serial operation, completely put in order both technically and in terms of appearance. Upon request, we are ready to send photos and videos, organize a video call with the warehouse, and also connect and show the equipment in operation with tests on the client's samples, if there is a desire to come in person and see everything.
We will help with loading onto your transport, we can also help with finding additional cargo. There is a forklift at the base, there will be no problems with sending.

KABAN MA2010. TWO-HEAD WELDING MACHINE
The machine is in excellent condition, almost new. Year of manufacture 2014. Warehouse storage, the machine is fully configured, adjusted, prepared for sale and shipment.
We will help with shipment, we use a forklift in the work.
Cashless sale without VAT, we provide a package of documents for shipment - supply agreement, UPD, acceptance certificates, TTN for transportation.

1. Used to assembly hardware systems such as Tilt, Tilt & Turn, Parallel Slide, Pivot, Slide-fold, Double Sash and Sliding Systems on different types, various sizes of window & door sash profiles without tape measure and pencil using, without need for molds and templates, provides speedy, high quality and standard assembling.2.Equipped with an industrial computer and a barcode scanner, it can be connected to other machines on the production line for data exchange3.Sash Assembly table4.Servo positioning espagnolette punching device, used for punching locking strips of various types of window sashes5.Full Automatic Screwing, Automatic screw feeding unit, Infrared indicator .6.Movable, adjustable triple handle hole drilling group with reinforced profile & upvc profile together.7.Latch Slot milling8.Two Holes Drilling On the sash with Stopper

Aluminium Profile Cutting And Machining Center

Its super-efficient workstation with integrates ERP door and window software + 3-angles efficient sawing + 3-station 4-direction 8-axis drilling and milling + laser scribingModel: SZA610Input Voltage: 380V/50Hz/3P or CustomizedTotal power: 45.55KWSaw blade specifications:∮550*4.4*∮30*120Sawing angle +45º 90°-45°Sectional size of sawed profile (width×height):180*150mmWeight about 12T

Tool Change CNC Aluminium Processing Machine HANS System

Model:GCGZD-CNC series, GCGZD-CNC-2500/3000/3500(X-way stroke)Power:380V 50Hz 3P or customizationCNC processing machine for aluminium profile, full automatic aluminium profile milling and drilling machine

SINON SHQXJ01 Welding & Corner Cleaning Line
/ Welding cleaning production line for pvc door and window / SHQXJ01 /
The production line is specialized in welding and cleaning outer corners of colored PVC profiles. It can be welded and formed into a rectangular window frame at one time, and the upper and lower welds are cleaned. Then, the completed window is transferred to the corner cleaning unit through the transfer workbench to complete the corner cleaning of the window. CNC Corner Cleaning

SINON SHQXJ02 Welding & Corner Cleaning Line UPVC
HORIZONTAL 4-HEAD WELDING MACHINE, DOUBLE CORNER CLEANING STATION

Features:
The production line is specialized in welding and cleaning outer corners of colored PVC profiles. It can be welded and formed into a rectangular window frame at one time, and the upper and lower welds are cleaned. Then, the completed window is transferred to the corner cleaning unit through the transfer workbench to complete the corner cleaning of the window. Double CNC Corner Cleaning Station.

CNC Aluminium Profile Milling Machine
SINON GCGZD-CNC-3000
Input power: 380V/50Hz or customized voltageTotal power: 7.5KwMain spindle speed: 0-24000rpmX axis processing range: 2500mmY axis processing range: 300mmZ axis processing range: 330mmDimension: 4600×1350×1900mmWeight: 2000kg